Geeks in Phoenix

Geek Blog


Resetting your network adapter in Windows XP

Network shell (Netsh) is a tool an administrator can use to configure and monitor network devices on Windows based computers at a command prompt. A common use of Netsh, is to reset the TCP/IP stack back to default settings.

But not only will Netsh reset the TCP/IP stack, but it can also completely reset your network adapter(s). It will also display the network diagnostics page in Windows XP too.

Using Netsh in Windows XP

To use Netsh, you will need to open a Command Prompt. There are two ways to do this:

  • Click the Start button, then Programs, then Accessories, then click on Command Prompt
  • or

  • Press Windows logo key + R. This will bring up the Run dialog box. Type CMD and click OK

Netsh commands in Windows XP

The following is a list of the Netsh commands you can use to reset your Windows XP network adapter:

Resets network interface informationnetsh int reset all

Resets TCP/IP and related components to a clean state.netsh int ip reset c:\resetlog.txt

Resets IPv6 configuration state.netsh int ipv6 reset

Displays the web page user interface.netsh diag gui

Resets Winsock Catalog to a clean state. All Winsock Layered Service Providers which were previously installed must be reinstalled. This command does not affect Winsock Name Space Provider entries.netsh winsock reset

How to reset Internet Protocol (TCP/IP) in Windows 7

One of the components of the Internet connection on your computer is a built-in set of instructions called TCP/IP. TCP/IP can sometimes become corrupted. If your connection to the Internet is really slow or you cannot connect to the Internet and you have tried all other methods to resolve the problem, TCP/IP might be causing it.

Because TCP/IP is a core component of Windows, you cannot remove it. However, you can reset TCP/IP to its original state. If you have any custom settings (default gateway, DNS server, etc.) you will need to manually set these again.

Use a manual method to reset TCP/IP

Note This section is intended for advanced computer users. If you are not comfortable with advanced troubleshooting, ask someone for help. In Windows Vista, a reset command is available in the IP context of the NetShell utility. Follow these steps to use the reset command to reset TCP/IP manually. You will have to restart your system to complete the reset.

  1. To open a command prompt, Click on the Start button, then All Programs, then Accessories, then click on Command Prompt.

  2. At the command prompt, copy and paste (or type) the following command and then press ENTER:

    netsh int ip reset c:\resetlog.txt

    Note: If you do not want to specify a directory path for the log file, use the following command:

    netsh int ip reset resetlog.txt

When you run the reset command, it rewrites two registry keys that are used by TCP/IP. This has the same result as removing and reinstalling the protocol. The reset command rewrites the following two registry keys:

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\
SYSTEM\CurrentControlSet\Services\DHCP\Parameters\

To run the manual command successfully, you must specify a file name for the log, in which the actions that netsh takes will be recorded. When you run the manual command, TCP/IP is reset and the actions that were taken are recorded in the log file, known as resetlog.txt in this article.

The first example, c:\resetlog.txt, creates a path where the log will reside. The second example, resetlog.txt, creates the log file in the current directory. In either case, if the specified log file already exists, the new log will be appended to the end of the existing file.

How to reset Internet Protocol (TCP/IP) in Windows Vista

One of the components of the Internet connection on your computer is a built-in set of instructions called TCP/IP. TCP/IP can sometimes become corrupted. If your connection to the Internet is really slow or you cannot connect to the Internet and you have tried all other methods to resolve the problem, TCP/IP might be causing it.

Because TCP/IP is a core component of Windows, you cannot remove it. However, you can reset TCP/IP to its original state. If you have any custom settings (default gateway, DNS server, etc.) you will need to manually set these again.

Use a manual method to reset TCP/IP

Note This section is intended for advanced computer users. If you are not comfortable with advanced troubleshooting, ask someone for help. In Windows Vista, a reset command is available in the IP context of the NetShell utility. Follow these steps to use the reset command to reset TCP/IP manually. You will have to restart your system to complete the reset.

  1. To open a command prompt, Click on the Start button, then All Programs, then Accessories, then click on Command Prompt.
  2. At the command prompt, copy and paste (or type) the following command and then press Enter:

    netsh int ip reset c:\resetlog.txt
    Note: If you do not want to specify a directory path for the log file, use the following command:
    netsh int ip reset resetlog.txt

When you run the reset command, it rewrites two registry keys that are used by TCP/IP. This has the same result as removing and reinstalling the protocol. The reset command rewrites the following two registry keys:

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\
SYSTEM\CurrentControlSet\Services\DHCP\Parameters\

To run the manual command successfully, you must specify a file name for the log, in which the actions that netsh takes will be recorded. When you run the manual command, TCP/IP is reset and the actions that were taken are recorded in the log file, known as resetlog.txt in this article.

The first example, c:\resetlog.txt, creates a path where the log will reside. The second example, resetlog.txt, creates the log file in the current directory. In either case, if the specified log file already exists, the new log will be appended to the end of the existing file.

How to reset Internet Protocol (TCP/IP) in Windows XP

One of the components of the Internet connection on your computer is a built-in set of instructions called TCP/IP. TCP/IP can sometimes become corrupted. If your connection to the Internet is really slow or you cannot connect to the Internet and you have tried all other methods to resolve the problem, TCP/IP might be causing it.

Because TCP/IP is a core component of Windows, you cannot remove it. However, you can reset TCP/IP to its original state. If you have any custom settings (default gateway, DNS server, etc.) you will need to manually set these again.

Use an automatic method to reset TCP/IP

To automatically reset Internet Protocol (TCP/IP) in Windows XP, click on the following link from Microsoft's website and select Run. This method requires a restart.
Microsoft Fix It

Use a manual method to reset TCP/IP

Note This section is intended for advanced computer users. If you are not comfortable with advanced troubleshooting, ask someone for help. In Windows XP, a reset command is available in the IP context of the NetShell utility. Follow these steps to use the reset command to reset TCP/IP manually:

  1. To open a command prompt, click Start and then click Run. Copy and paste (or type) the following command in the Open box and then press ENTER:
    cmd
  2. At the command prompt, copy and paste (or type) the following command and then press ENTER:
    netsh int ip reset c:\resetlog.txt
    Note: If you do not want to specify a directory path for the log file, use the following command:
    netsh int ip reset resetlog.txt

When you run the reset command, it rewrites two registry keys that are used by TCP/IP. This has the same result as removing and reinstalling the protocol. The reset command rewrites the following two registry keys:

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\
SYSTEM\CurrentControlSet\Services\DHCP\Parameters\

To run the manual command successfully, you must specify a file name for the log, in which the actions that netsh takes will be recorded. When you run the manual command, TCP/IP is reset and the actions that were taken are recorded in the log file, known as resetlog.txt in this article.

The first example, c:\resetlog.txt, creates a path where the log will reside. The second example, resetlog.txt, creates the log file in the current directory. In either case, if the specified log file already exists, the new log will be appended to the end of the existing file.

Customer service is #1

Here at Geeks in Phoenix, we take pride in providing excellent customer service. From computer repair, virus removal and data recovery, we aim to give the highest quality of service.

Bring your computer to us and save

Our in-shop computer repair service  is based on the time we work on your computer, not the time it takes your computer to work!

Contact us

Geeks in Phoenix
4722 East Monte Vista Road
Phoenix, Arizona 85008
(602) 795-1111

Like Geeks in Phoenix on Facebook

Follow Geeks in Phoenix on Twitter

Watch Geeks in Phoenix on YouTube

Geeks in Phoenix is an IT consulting company specializing in all aspects of Computer Repair / PC Repair / Laptop Repair. Since 2008, our expert computer repair technicians have been providing outstanding Computer Repair, Virus Removal, Data Recovery, Photo Manipulation and Website Support.

Geeks in Phoenix have the best computer repair technicians providing computer repair and service in Phoenix, Scottsdale and Tempe Arizona. We offer In-Shop, On-Site and Remote (with stable Internet connection) computer repair service.

Copyright © 2016 Geeks in Phoenix LLC